Steam cylinder?
-
- Posts: 227
- Joined: Mon Jan 06, 2003 8:09 pm
- Location: Pennsylvania
- Contact:
Re: Steam cylinder?
That's why I suggested the Tiny Power piece, I inquired a couple years back, and $60 seems to stick in my mind (whether that was the cylinder set or just the block, I don't remember.).
BUT compared to $950 for the entire engine (castings & drawings only) it is SOME savings [img]/ubb/images/graemlins/wink.gif"%20alt="[/img]
BUT compared to $950 for the entire engine (castings & drawings only) it is SOME savings [img]/ubb/images/graemlins/wink.gif"%20alt="[/img]
Re: Steam cylinder?
Check out this website where Wilifred "carves out a cylinder from a chunk of cast iron for his "Two Times Engine."
http://www.ussers.skynet.be/modelbouw.wilfried/
Al Messer
http://www.ussers.skynet.be/modelbouw.wilfried/
Al Messer
Al Messer
"One nation, under God"
"One nation, under God"
Re: Steam cylinder?
How did I just become a Second Year Apprentice over night??
Al Messer
"One nation, under God"
"One nation, under God"
-
- Posts: 227
- Joined: Mon Jan 06, 2003 8:09 pm
- Location: Pennsylvania
- Contact:
Re: Steam cylinder?
You posted once too often
Re: Steam cylinder?
They prob'ly 'eard you bought a SHAPER
[img]/ubb/images/graemlins/grin.gif"%20alt="[/img] [img]/ubb/images/graemlins/grin.gif"%20alt="[/img] [img]/ubb/images/graemlins/grin.gif"%20alt="[/img] [img]/ubb/images/graemlins/grin.gif"%20alt="[/img]
[img]/ubb/images/graemlins/grin.gif"%20alt="[/img] [img]/ubb/images/graemlins/grin.gif"%20alt="[/img] [img]/ubb/images/graemlins/grin.gif"%20alt="[/img] [img]/ubb/images/graemlins/grin.gif"%20alt="[/img]
Tel
-
- Posts: 4090
- Joined: Sat Jan 04, 2003 10:29 pm
- Location: Tennessee, Obion County, Town of Troy
Re: Steam cylinder?
Well, Al DID bought a shaper, a South Bend 7 incher so you (TEL) and I have gotta quit poking fun at him. Personally, I think he just bought it so we couldn;t stick it in his face every time he mentioned that you and I were on diets! Ah well, Al welcome to the exclusive "Shaper Lovers Society".
Unka Jesse
Unka Jesse
"The same hammer that breaks the glass, forges the steel" Russian proverb
-
- Posts: 4090
- Joined: Sat Jan 04, 2003 10:29 pm
- Location: Tennessee, Obion County, Town of Troy
Re: Steam cylinder?
Richard, I can't remember what issues were involved, but the VW articles mentioned were in Live Steam about 6 years ago.
Unka Jesse
Unka Jesse
"The same hammer that breaks the glass, forges the steel" Russian proverb
Re: Steam cylinder?
Al
I considered making it from a billet, since I must have 1/2 a ton of cast iron bar stock laying around. Most of it 3" diameter from about 6 to 9" long. Actualy welding up a cylinder might be easier. I will have to give that some thought.
Also I couldn't get the link to work. I will try it again later.
Is there a good site to get a real good idea for making poppet valves?
Richard W.
I considered making it from a billet, since I must have 1/2 a ton of cast iron bar stock laying around. Most of it 3" diameter from about 6 to 9" long. Actualy welding up a cylinder might be easier. I will have to give that some thought.
Also I couldn't get the link to work. I will try it again later.
Is there a good site to get a real good idea for making poppet valves?
Richard W.