Search found 10480 matches
- Mon Apr 22, 2024 12:24 pm
- Forum: Live Steam
- Topic: fuel topic
- Replies: 52
- Views: 2709
Re: fuel topic
GIGGLE....and coal with Sulphur is not acidic?
- Mon Apr 22, 2024 8:57 am
- Forum: Live Steam
- Topic: fuel topic
- Replies: 52
- Views: 2709
Re: fuel topic
is what I remember steve doing - although it had troughs in it to increase the surface area....
seem to remember is looking like an accordion from the top with holes in the V sides....
didn't smell like a popcorn engine though
seem to remember is looking like an accordion from the top with holes in the V sides....
didn't smell like a popcorn engine though
- Mon Apr 22, 2024 8:00 am
- Forum: Live Steam
- Topic: fuel topic
- Replies: 52
- Views: 2709
Re: fuel topic
I have seen Steve Bratina running a loco on it maybe 20 years ago....??
required a very funky looking grate IIRC
required a very funky looking grate IIRC
- Sun Apr 21, 2024 6:22 pm
- Forum: The Photo Album
- Topic: tractor engine top end rebuild
- Replies: 50
- Views: 2664
Re: tractor engine top end rebuild
Did you put new seals in the hydraulic pump?
Is the hyd pump belt driven or mounted on the engine black and gear driven?
Is the hyd pump belt driven or mounted on the engine black and gear driven?
- Sun Apr 21, 2024 6:20 pm
- Forum: General Discussion
- Topic: A spindle oil question
- Replies: 13
- Views: 237
Re: A spindle oil question
Yesterday I spent $125 on gasoline to run my lawn mower for the next 3 months.
It cut grass like a banshee, but us very thirsty.
$5 for a coffee makes it seem cheap to take care of the bearings in our machines...
It cut grass like a banshee, but us very thirsty.
$5 for a coffee makes it seem cheap to take care of the bearings in our machines...
- Sun Apr 21, 2024 4:40 pm
- Forum: General Discussion
- Topic: Repair Montgomery Wards Powr-Kraft split-phase motor with Thermotron protection
- Replies: 3
- Views: 82
Re: Repair Montgomery Wards Powr-Kraft split-phase motor with Thermotron protection
Of course. Where do you think the smoke came from?
Individual windings are separated by a thin layer of varnish.
Individual windings are separated by a thin layer of varnish.
- Sun Apr 21, 2024 3:37 pm
- Forum: Live Steam
- Topic: Double Flaring on Copper Tubing
- Replies: 12
- Views: 545
Re: Double Flaring on Copper Tubing
Steggy is correct about improper installation of copper and its possible eventual failure and use of stainless, however the tried and true use of copper is just fine. Simple soft soldering is more than enough for this application where copper can be used. Look at IBLS www site for bill van brocklin'...
- Sun Apr 21, 2024 6:40 am
- Forum: Live Steam
- Topic: Odd question
- Replies: 13
- Views: 542
Re: Odd question
If every dimension on a locomotive was held to ±.0001" the engine would run perfectly, assuming it was dimensioned properly. ...and each locomotive would cost as much as a Boeing 747. :D Chuckle! True, that, but learning proper terminology is free! H and who would determine the dimension &...
- Sun Apr 21, 2024 6:36 am
- Forum: Live Steam
- Topic: fuel topic
- Replies: 52
- Views: 2709
Re: fuel topic
good luck with penn coal. they are now shipping only by the RR car load, SO IF YOU WANT 20+ tons, you are good to go. Gone are the days of a few bags or pallet load. They WERE our source of Pocahontas coal for decades.... venus tile and marble only sells what they have, they are not a mine / major d...
- Sat Apr 20, 2024 9:01 pm
- Forum: General Discussion
- Topic: A spindle oil question
- Replies: 13
- Views: 237
Re: A spindle oil question
If it is ball and roller bearings only...it is a good point.
However if sleeve bearings are involved, as may be in a lathe, or in my case old sleeve bearing pedestal grinders as well, prefer to stay with specific spindle oil.
However if sleeve bearings are involved, as may be in a lathe, or in my case old sleeve bearing pedestal grinders as well, prefer to stay with specific spindle oil.
- Sat Apr 20, 2024 7:40 pm
- Forum: General Discussion
- Topic: A spindle oil question
- Replies: 13
- Views: 237
Re: A spindle oil question
Find a local machine shop and go in with a gallon bottle and a $20 bill.
- Sat Apr 20, 2024 7:37 pm
- Forum: General Discussion
- Topic: A spindle oil question
- Replies: 13
- Views: 237
Re: A spindle oil question
You and me both.
Get some cutting oil while you are at it, and some drills.
I keep a list on my computer ....
Get some cutting oil while you are at it, and some drills.
I keep a list on my computer ....