Jet 1236 lathe

All discussion about lathes including but not limited to: South Bend, Hardinge, Logan, Monarch, Clausing and other HSM lathes, including imports

Moderators: GlennW, Harold_V

User avatar
Bill Shields
Posts: 10442
Joined: Fri Dec 21, 2007 4:57 am
Location: 39.367, -75.765
Contact:

Re: Jet 1236 lathe

Post by Bill Shields »

Only 101?
Too many things going on to bother listing them.
User avatar
Steggy
Posts: 1973
Joined: Tue Jun 28, 2011 9:19 pm
Location: JB Pritzker’s Hellhole
Contact:

Re: Jet 1236 lathe

Post by Steggy »

Dan2006 wrote: Sat Sep 24, 2022 12:48 pmIf I remember right a gentleman who I think was dinosaur, he replied to me here. I think he had a write up somewhere and changed to a vfd. I could be wrong. If nothing else I will do that and copy that one. I just have to go and find it.

See here. I have not yet installed a VFD—medical maladies have kept me out of the shop for about four months. I’m hoping to soon get back to it.
———————————————————————————————————————————————————————
Music isn’t at all difficult.  All you gotta do is play the right notes at the right time!  :D
User avatar
Steggy
Posts: 1973
Joined: Tue Jun 28, 2011 9:19 pm
Location: JB Pritzker’s Hellhole
Contact:

Re: Jet 1236 lathe

Post by Steggy »

Bill Shields wrote: Sat Sep 24, 2022 4:34 pmOnly 101?

That was all I could think of. :D
———————————————————————————————————————————————————————
Music isn’t at all difficult.  All you gotta do is play the right notes at the right time!  :D
User avatar
Bill Shields
Posts: 10442
Joined: Fri Dec 21, 2007 4:57 am
Location: 39.367, -75.765
Contact:

Re: Jet 1236 lathe

Post by Bill Shields »

My wife has 101 uses in the kitchen after I have used it in the shop...
Too many things going on to bother listing them.
Dan2006
Posts: 17
Joined: Wed Sep 21, 2022 3:39 pm

Re: Jet 1236 lathe

Post by Dan2006 »

NP317 wrote: Sat Sep 24, 2022 11:12 am What Bill said.
Call Grizzly's support team for a friendly and useful discussion.
Grizzly does carry replacement motors that are likely not listed on their website.
And their original warehouse and business center are located in Bellingham, WA, just off I-5, so at least on your same West Coast USA.
RussN
Russ Thank you very much for Grizzly s contact info, I will be contacting them on Monday after school.
Dan2006
Posts: 17
Joined: Wed Sep 21, 2022 3:39 pm

Re: Jet 1236 lathe

Post by Dan2006 »

Hi Dinosaur,

I'm sorry for your delay.

I'm sure I was wrong about who wrote the vfd installation. I think it was at a different forum. I must have read some of your postings because the name is familiar.

I should have made notes, but I didn't think about it.

Believe me I'm making notes of everyone's replies. I really appreciate everyone posting things. And I mean everyone. All from Turkey bastares to rust cleaners, oil taking out sight glasses and everything else.

So, tonight I'm going to get back to cleaning it up and getting together all the parts out of the box I found.

I just want to say thank you to everyone again.

I'll take more pictures as I go.
User avatar
Steggy
Posts: 1973
Joined: Tue Jun 28, 2011 9:19 pm
Location: JB Pritzker’s Hellhole
Contact:

Re: Jet 1236 lathe

Post by Steggy »

BUMP!

Did the OP ever get this lathe going?
———————————————————————————————————————————————————————
Music isn’t at all difficult.  All you gotta do is play the right notes at the right time!  :D
User avatar
rmac
Posts: 785
Joined: Tue Jun 26, 2012 12:48 am
Location: Phoenix, Arizona

Re: Jet 1236 lathe

Post by rmac »

The OP hasn't been active here since September, so we'll probably never know.
Post Reply