Champion Tool Works 12" Lathe - Carriage Auto Feed
Champion Tool Works 12" Lathe - Carriage Auto Feed
Hi, I just acquired a Champion Tool Works 12" Lathe from early 1900.
I do not have any documentation on usage, nor have I been able to find any.
I DO have the auto feed working for the cross slide, and I can start it, stop it, and change its directions.
I can't figure out how to get the autofeed working for the Carriage itself.
Does anyone have experience or instructions for this model?
I am including a picture of the full Lathe and a close up of the Carriage Controls
Appreciate the help, this is my first Post.
I do not have any documentation on usage, nor have I been able to find any.
I DO have the auto feed working for the cross slide, and I can start it, stop it, and change its directions.
I can't figure out how to get the autofeed working for the Carriage itself.
Does anyone have experience or instructions for this model?
I am including a picture of the full Lathe and a close up of the Carriage Controls
Appreciate the help, this is my first Post.
-
- Posts: 1955
- Joined: Wed Mar 15, 2006 11:10 pm
- Location: Farmington, NM
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
There should be a lever, typically about in the place of the one marked deactivated, that should switch the auto feed function from carriage to cross slide. You may need to look inside the carriage and see if there are any parts obviously missing, and try to figure out what the previous owner(s) did.
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
Thanks Russ, I will take a closer look. Perhaps that lever got bumped during transport and is stuck in the cross slide position.
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
Hi Russ, I investigated that lever more carefully, and it was just very tight, however, it is used to disengage the manual Carriage feed entirely but does not allow for any auto feed.
Would you have any other ideas?
Thanks,
DR
Would you have any other ideas?
Thanks,
DR
-
- Posts: 2366
- Joined: Tue Jan 20, 2009 9:33 pm
- Location: Phoenix ,AZ
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
You sure that lever does not have 3 positions ? Neutral in center,slide one way cross the other that is the way those are usually set up. some lathes however did not have power cross feed.
www.chaski.com
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
Doesn't look like it, at the extreme, the power cross feed still operates.
-
- Posts: 2366
- Joined: Tue Jan 20, 2009 9:33 pm
- Location: Phoenix ,AZ
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
Well with a antique machine like that anything is possible. Atlas/Craftsman lathes , some had power crossfeeds but, all used the half nuts for slide feed. Your lathe may work the same.
www.chaski.com
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
does that lower left hand lever move through 180 degrees? how much travel does it have?
I found a photo of another 12 inch lathe showing the lever 180 degrees from the one in your photo. Maybe something is stuck in the apron.
Peter
I found a photo of another 12 inch lathe showing the lever 180 degrees from the one in your photo. Maybe something is stuck in the apron.
Peter
Re: Champion Tool Works 12" Lathe - Carriage Auto Feed
BTW, I was going ask. Did that machine come with a tail stock?
———————————————————————————————————————————————————————
Music isn’t at all difficult. All you gotta do is play the right notes at the right time!
Music isn’t at all difficult. All you gotta do is play the right notes at the right time!