Help!!! A850SX Lathe

All discussion about lathes including but not limited to: South Bend, Hardinge, Logan, Monarch, Clausing and other HSM lathes, including imports

Moderators: GlennW, Harold_V

JonMac1996
Posts: 20
Joined: Sat Aug 29, 2020 5:24 pm

Re: Help!!! A850SX Lathe

Post by JonMac1996 »

Bob D. wrote: Mon Sep 14, 2020 8:00 am You should be getting another screen..... Is the edit key on? Not sure if that limits access but it might.
I'll dig out the Operators Manual and see if there are clues there.

Here is a page on SFP
Nothing happens, no page is shown to me, just "beeps" the key and nothing changes.

Even in program editing mode, I tried. I tried with the CTL key together and it also doesn't work, as it says in the manual, just press to work ... 🤔
Bob D.
Posts: 381
Joined: Thu Jun 21, 2012 10:43 pm
Location: Saco, ME. USA

Re: Help!!! A850SX Lathe

Post by Bob D. »

Do you have the key for the switch on the operator panel? It's not there in your panel picture. Open the panel and jump the two wires on the key switch if you don't have the key.
3/4" Juliet II 0-4-0
3/4" Purinton Mogul "Pogo"
3/4" Hall Class 10 wheeler
3/4" Evans Caribou/Buffalo 2-8-0
3/4" Sweet Violet 0-4-0
3/4" Hunslet 4-6-0
3/4" Kozo A3. Delayed construction project

1 1/2" A5 Camelback 0-4-0
JonMac1996
Posts: 20
Joined: Sat Aug 29, 2020 5:24 pm

Re: Help!!! A850SX Lathe

Post by JonMac1996 »

Bob D. wrote: Mon Sep 14, 2020 8:55 am Do you have the key for the switch on the operator panel? It's not there in your panel picture. Open the panel and jump the two wires on the key switch if you don't have the key.
This key:
IMG_20200914_111239719~2.jpg
If this is not the case, I will have to ask maintenance to open the panel if this is the case.
Bob D.
Posts: 381
Joined: Thu Jun 21, 2012 10:43 pm
Location: Saco, ME. USA

Re: Help!!! A850SX Lathe

Post by Bob D. »

Yes, that one. If nothing happens jumping the wires together try lifting one wire. I don't remember if locked is an open or closed contact. Generally it is open to be locked.
Pretty sure this is your access problem.
3/4" Juliet II 0-4-0
3/4" Purinton Mogul "Pogo"
3/4" Hall Class 10 wheeler
3/4" Evans Caribou/Buffalo 2-8-0
3/4" Sweet Violet 0-4-0
3/4" Hunslet 4-6-0
3/4" Kozo A3. Delayed construction project

1 1/2" A5 Camelback 0-4-0
JonMac1996
Posts: 20
Joined: Sat Aug 29, 2020 5:24 pm

Re: Help!!! A850SX Lathe

Post by JonMac1996 »

Bob D. wrote: Mon Sep 14, 2020 9:21 am Yes, that one. If nothing happens jumping the wires together try lifting one wire. I don't remember if locked is an open or closed contact. Generally it is open to be locked.
Pretty sure this is your access problem.
Ok, I'll try. I looked for her original key and I didn't find it, but I already activated the maintenance, they will look after lunch. I hope that's it.

As soon as we do I tell you if it worked ...
Bob D.
Posts: 381
Joined: Thu Jun 21, 2012 10:43 pm
Location: Saco, ME. USA

Re: Help!!! A850SX Lathe

Post by Bob D. »

So where are you at getting that Cinturn programing working? Sure hope your still not waiting on Maintenance to arrive.....gives my field a bad rap!
3/4" Juliet II 0-4-0
3/4" Purinton Mogul "Pogo"
3/4" Hall Class 10 wheeler
3/4" Evans Caribou/Buffalo 2-8-0
3/4" Sweet Violet 0-4-0
3/4" Hunslet 4-6-0
3/4" Kozo A3. Delayed construction project

1 1/2" A5 Camelback 0-4-0
Post Reply